Frequently bought together
Description
- Multi-Size Angle Guides
- Diamond Grinding Discs
- Drill-Powered Shaft
- 3-in-1 Sharpening
- Pocket Portable
Don't throw away that dull drill bit. The Restore & Reuse Drill Bit Sharpener runs off the drill you already own, grinding a fresh edge with 140-mesh diamond discs while 3 interchangeable guides hold bits from 2 to 16 mm, 0.08 to 0.63 inch at a set angle.
Angles Set for You
Once the bit is seated, the Restore & Reuse Drill Bit Sharpener holds the bevel so your hand doesn't have to. Three interchangeable guide blocks fit the frame, each with grooves sized for a band of diameters, together covering bits from 2 to 16 mm, 0.08 to 0.63 inch. The groove locks the cutting tip against the diamond surface at a preset angle, so each lip meets the abrasive the same way, with no measuring. Pick the block, drop the bit in, and the guide does the aligning. Freehand filing usually fails on exactly this step, especially with the thin bits you use for pilot holes in trim or cabinet hardware, where a few degrees off makes the tip skate. What comes back is an even pair of cutting edges and a hole that starts on your pencil mark.
Edges That Bite Again
Inside the frame, a 140-mesh diamond grinding disc gives the Restore & Reuse Drill Bit Sharpener its cutting power. Diamond is harder than the high-speed steel most twist bits are made from, so the disc removes metal from a blunt tip instead of polishing it, and the high-hardness grit is designed to resist the glazing that dulls a soft stone. If you doubt that a light attachment can grind hardened steel, look at the abrasive, because that is the part doing the grinding. Secure the guide, run the drill at a moderate speed and let the disc cut. Running it flat out is what overheats an edge. It is built for standard twist bits, not masonry hammer bits or heavy-duty industrial cobalt. Each pack includes 2 discs. Your old bits go back to biting into pine, oak and sheet metal instead of smoking on the surface.
Power You Already Own
There's no motor to buy, because the Restore & Reuse Drill Bit Sharpener borrows the one in your drill. An alloy drive shaft goes into the chuck of a standard electric hand drill, corded or cordless, and carries its rotation straight to the diamond disc. A metal shaft helps keep the spin true under load, which helps limit wobble while a bit is being ground. That turns the drill you already charge for weekend projects into a grinder, without a 9 kg, 20 lb bench machine bolted to the workbench and the outlet it needs. For a maintenance technician or a woodworker moving between jobs, it means touching up bits on site instead of carting dull ones home. The money you would have spent on new bit sets stays in your pocket for lumber and hardware.
One Station, Three Edges
Drill bits are only part of the job. Alongside the bit guides, the Restore & Reuse Drill Bit Sharpener has dedicated channels for kitchen knives and scissors, so the same diamond abrasive that restores a twist bit can also touch up a blade. Each channel guides the steel against the abrasive at a controlled angle, so you are not holding the blade at a guessed angle freehand. Think of the utility shears that live in the garage, or the kitchen knife that has started crushing tomatoes instead of slicing them. A badly chipped or specialty blade still belongs with a professional sharpener or a whetstone. For everyday edges, one compact tool now covers three jobs, and the drawer gets a little lighter.
Sharpen Anywhere
At 13 x 6 x 4 cm, 5.12 x 2.36 x 1.57 inch and 250 g, 8.82 oz, the Restore & Reuse Drill Bit Sharpener fits in a tool bag pocket or the same drawer where the dull bits are waiting. Its compact frame carries the guide grooves and the diamond disc in one body, so there is no stand to assemble and nothing to bolt down. Chuck the alloy shaft, choose your guide and start grinding. It earns its spot in the van of a tradesman working across several sites, or on the shelf of a one-car garage with no room left for a bench grinder. Pick orange if you want it easy to find in a crowded toolbox, or black if your kit runs dark. Wherever the drill travels, a fresh edge travels with it.
Technical characteristics:
Type: Drill-powered sharpening attachment for drill bits, knives and scissors
Power source: Standard electric hand drill, corded or cordless
Drive shaft: Alloy
Compatible bits: Standard twist drill bits
Weight: 250 g | 8.82 oz
Drill bit capacity: 2-16 mm | 0.08-0.63 inch
Product content:
1x Restore & Reuse Drill Bit Sharpener
2x 140-mesh diamond grinding discs
3x interchangeable angle guide blocks
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Not Happy with your purchase? We take it back!
Your satisfaction is our top priority
Item covered by the Purchase Protection Program
Shop on Ozerty with confidence, knowing that we're here to support you if any issues arise
Our delivery guarantee
- Shipping 72h
- Tracked parcel
- Packed with care
- 5£ credit in case of any delay!
Any Questions?
Our support team answers you 9:00am to 6:00pm Monday to Friday:
contact.uk@ozerty.com
We found other products you might like!
